{0}------------------------------------------------
## **SECTION A DETAILS** 

**FACILITY INFORMATION [Detailed discussion of any items in Section A]** 

RTX Corporation, Pratt and Whitney Division (Pratt and Whitney) is a manufacturer of aircraft engines and is headquartered in East Hartford, CT. Pratt and Whitney is operating a new turbine airfoil production facility in Asheville, North Carolina in Buncombe County. 

The purpose of this modification is to update a process that has been changed from what was submitted in the application during the construction of the facility. When the original application was submitted, they were based on pre-construction designs, and as such, some sources have changed during the construction process. The changes that will be made to the permit for this modification are as follows: 

- ALUM1 – The aluminide coating process uses an activator agent that has the potential to create Hydrogen Fluoride (HF) from a side reaction. The potential HF emissions associated with this process are now above the TPER due to recipe updates. Air dispersion modeling was performed to show that the facility is in compliance. Along with this, there is also a slight increase of 0.07 tons of emissions  for PM, PM2.5, and PM10. A limit of 15.9 lbs of activator per 24 hour period for the ALUM1 process will be put in place to keep HF emissions below the threshold. 

The application was received on July 31, 2025. The zoning consistency determination was received on August 20, 2025. The application fee was received on August 22, 2025 and that is when the application was deemed complete. 

Below is a description of the facility with the newly updated information from this permit application: 

The facility will manufacture metal parts, which include casting operations, where the body of the parts are made through metal casting, and then go through grinding, coating and quality inspections before being shipped to customers. 

Part casting uses a method of casting known as lost wax investment casting, which forms the general part that will be ready for final finishing. Wax is first injected into a die, and once cooled, the wax patterns removed. The wax pattern is dipped into a ceramic slurry to build a shell around the wax. Once the shell dries, the part is moved to an electric steam autoclave to melt out the wax. The autoclave chamber is depressurized and the steam vents outdoors. A small percentage of wax is volatilized as VOC emissions. The hollow shells are then moved to a natural gas furnace to remove any remaining wax residue. The furnace exhaust is processed through an afterburner which combusts VOC from the wax then vents to atmosphere. Emissions from the furnace will include nitrogen oxides (NOx), carbon monoxide (CO) and particulates from the combustion of natural gas. 

The hollow ceramic shells then move to casting, where in an electric metal induction vacuum furnace, ingots are melted down and poured into the ceramic shell’s cavity while a vacuum pump runs to remove the air. The vacuum pump for the furnaces vents outdoors. The furnaces are expected to emit minimal PM emissions after passing through an in-line particulate filter. Also, expected is a minimal amount of NOx and VOC that are thermally generated within the furnace chamber. 

The parts are then heat treated in an electric vacuum furnace, after which they are cooled before the ceramic shell is removed from the metal. The vacuum pump for the furnace vents outdoors. PM emissions from the shell removal process are captured in a hood controlled by filters that do not vent outdoors. The parts go to the Post-cast area where parts are machined and finished. Shell removal and machining activities in the Post-cast area are vented to dust collectors to control PM emissions. These dust collectors will vent indoors. The part then enters a vacuum sealed liquid caustic autoclave where the internal ceramic structure is removed. The parts are then inspected for quality using a series of tests including grain etching and a Florescent Penetrant Inspection (FPI) process. The ventilation hood over the grain etch lines will vent to the outside and be controlled by a wet scrubber. 

After the parts exit the casting process, the parts are baked in an electric oven to remove any de minimis oils including oils from fingerprints. The parts then move to ceramic and/or metal solids coating processes
{1}------------------------------------------------
that are connected to an in-line particulate air filter. The metallic thermal spray operations occur under vacuum and will vent outdoors. The atmospheric ceramic and/or metal spray applications are collected in a dust collector and vented indoors. The parts are heat treated in an electric oven to seal the coating. These electric ovens have a vacuum pump that vent outdoors. 

The parts are then sent to enclosed oil-filled grinding machines where they are ground to their final shape. The grinding machines utilize a mist collector that will vent indoors. 

The next step includes drilling holes into the parts with a laser. Prior to drilling, some parts are filled with wax. The laser drilling machines are enclosed and vent to a dust collector that vents indoors. Once the drilling is complete a natural gas fired furnace burns off the wax. The parts then move to a metal solids coating process that occurs in a vacuum chamber connected to a dust collector that will vent outdoors. The parts are then cleaned and inspected and prepared for shipment. 

To support the proposed operations, eight natural gas fired emergency engines will be installed should the facility lose power. There will be four 2,100-brake horsepower engines, and four 229-brake horsepower engines. Each of these engines will meet the appropriate NSPS and NESHAP emission standards, respectively. The engines are only expected to run in non-emergency mode during testing and maintenance of the engines.
{2}------------------------------------------------
## **SECTION B DETAILS** 

## **APPLICATION INFORMATION** 

**[List all emission sources (permitted and exempt) reviewed as a result of this application, their associated control devices and pollutants.  Provide a detailed discussion of any other items in Section B at bottom under “Application Notes”]** 

|**SECTION B DETAILS**|**SECTION B DETAILS**|**SECTION B DETAILS**|**SECTION B DETAILS**|
|---|---|---|---|
|**APPLICATION INFORMATION**<br>**[List all emission sources (permitted and exempt) reviewed as a result of this application, their**<br>**associated control devices and pollutants.  Provide a detailed discussion of any other items in**<br>**Section B at bottom under“Application Notes”] **||||
|**Emission**<br>**Source ID**|**Emission Source Description**<br>**1.**<br>**Type, manufacturer, capacity**<br>**2.**<br>**Control device with ID(ifany)**|**Pollutant(s)**<br>**Emitted**|**Miscellaneous Notes**|
|WIP|One (1) Wax Injection Process<br>(WIP) consisting of Ten (10) Wax<br>Injection Machines (WAX1 –<br>WAX10)|VOCs||
|SBP|One (1) Shell Build Process (SBP)<br>consisting of two (2) Wax Mold<br>Etch Baths (WAXETCH1 and<br>WAXETCH2), two (2) Steam<br>Dewax Autoclaves (WAXMELT1<br>and WAXMELT2) and seven (7)<br>Natural Gas Fired Shell Kilns<br>(SHELL1 – SHELL7) controlled by<br>natural gas-fired after burners total<br>heat input rated at 1.1 MMBtu/hr<br>each (C-1 through C-7).|CO, NOX, PM,<br>PM10, PM2.5,<br>SO2, VOCs,<br>HAPs/TAPs,<br>GHGs||
|PCP|One (1) Part Casting Process<br>(PCP) consisting of ten (10)<br>Electric Vacuum Furnaces<br>(FURNACE1–FURNACE10)|NOX, PM, PM10,<br>PM2.5, VOCs,<br>HAPs/TAPs||
|POCP|One (1) Post Casting Process<br>(POCP) consisting of two (2) Grain<br>Etching Lines (GRAINETCH1 and<br>GRAINETCH2), one FPI Spray<br>Application Line (FPI1), and three<br>(3) Post Cast Electric Vacuum<br>Furnaces (VACFURN1 –<br>VACFURN3)|VOCs||
|CP|One (1) Coating Process (CP)<br>consisting of thirteen (13) Electric<br>Ovens (OVEN1-OVEN13), six (6)<br>Thermal Spray Processes under<br>vacuum (VPS1 – VPS6) controlled<br>by in-line particulate filters (C-8<br>through C-13), five (5) APPS<br>Ceramic Coating Process (APPS1<br>– APPS5) controlled by dust<br>collectors (C-37 through C-41),<br>and one (1) Aluminide Coating<br>Process (ALUM1)|PM, PM10,<br>PM2.5, VOCs,<br>HAPs/TAPs|VPD1 – VPD23 which were listed<br>in the previous permit were<br>removed since they are vented<br>indoors. VSP1 – VSP6 are also<br>vented indoors, but remain on the<br>permit since they are subject to<br>40 CFR Part 63, Subpart<br>WWWWWW.|
|MP|One (1) Machining Process (MP)<br>consisting of one FPI Spray<br>Application Line (FPI2), one (1)<br>Wax Injection Machine (WAX11),<br>two (2) Natural Gas Fired Wax<br>Burnout Furnaces (WAXFURN1<br>and WAXFURN2) controlled by<br>natural gas-fired after burners total<br>heat input rated at 0.5 MMBtu/hr<br>each (C-42 through C-43)|CO, NOX, PM,<br>PM10, PM2.5,<br>SO2, VOCs,<br>HAPs/TAPs,<br>GHGs|Page 23 of 120 lists total heat<br>input for WAXFURN1 and<br>WAXFURN2 as 0.46 MMBtu/hour<br>each.|
{3}------------------------------------------------
|EBPVD|One (1) Electron-beam Physical<br>Vapor Deposition Process<br>(EBPVD) consisting of thirteen (13)<br>Electric Ovens (OVEN14-<br>OVEN26) and five (5) Thermal<br>Spray Processes under vacuum<br>(EBPVD 1–EBPVD5)|PM, PM10,<br>PM2.5, VOCs|The HEPA filters previously<br>associated with EBPVD1 –<br>EBPVD5 were removed with this<br>modification.|
|---|---|---|---|
|EGEN1,<br>EGEN2,<br>EGEN3,<br>EGEN4|Four (4) 1,118 hp natural gas-fired<br>emergency generators|CO, NOX, PM,<br>PM10, PM2.5,<br>SO2, VOCs,<br>HAPs/TAPs,<br>GHGs|The engines listed have been<br>updated with this modification.|
|EGEN5,<br>EGEN6,<br>EGEN7,<br>EGEN8|Four (4) 229 hp natural gas-fired<br>emergency generators|CO, NOX, PM,<br>PM10, PM2.5,<br>SO2, VOCs,<br>HAPs/TAPs,<br>GHGs|The engine currently is exempt<br>from permitting requirements per<br>the AB Air Quality Code 17.0102<br>(c)(2)(B)(v)(I).|
|FWP|One (1) 120 hp natural gas-fired<br>emergency fire water pump|CO, NOX, PM,<br>PM10, PM2.5,<br>SO2, VOCs,<br>HAPs/TAPs,<br>GHGs|The engine currently is exempt<br>from permitting requirements per<br>the AB Air Quality Code 17.0102<br>(c)(2)(B)(v)(I). The engine was not<br>installed and is being removed<br>from the insignificant activity list.|
|NA|A grit blast and laser parts<br>cleaning process with emissions<br>captured by dust collector and<br>vented indoors.|NA|This process is exempt from<br>permitting requirements per the<br>AB Air Quality Code 17.0102<br>(c)(1)(L)(ix).|
|NA|A shot and dot peen process with<br>emissions captured by dust<br>collector and vented indoors|NA|This process is exempt from<br>permitting requirements per the<br>AB Air Quality Code 17.0102<br>(c)(1)(L)(ix).|
|NA|Machining, grinding, and EDM of<br>metal parts using lubricating oil<br>process with emissions captured<br>by mist eliminators and a HEPA<br>filter and vented indoors|NA|This process is exempt from<br>permitting requirements per the<br>AB Air Quality Code 17.0102<br>(c)(1)(L)(ix).|
|NA|A laser machining process with<br>emissions captured by dust<br>collector and vented indoors|NA|This process is exempt from<br>permitting requirements per the<br>AB Air Quality Code 17.0102<br>(c)(1)(L)(ix).|
|NA|One (1) electric brazing oven|NA|This oven is exempt from<br>permitting requirements per the<br>AB Air Quality Code 17.0102<br>(c)(1)(L)(x).|
|NA|One (1) electric oven for heat<br>treatment of casted parts|NA|This oven is exempt from<br>permitting requirements per the<br>AB Air Quality Code 17.0102<br>(c)(1)(L)(x).|
|NA|A shell building process with<br>emissions captured by dust<br>collector vented indoors|NA|This process is exempt from<br>permitting requirements per the<br>AB Air Quality Code 17.0102<br>(c)(1)(L)(ix).|
|NA|A shell removal process with<br>emissions captured by dust<br>collector vented indoors|NA|This process is exempt from<br>permitting requirements per the<br>AB Air Quality Code 17.0102<br>(c)(1)(L)(ix).|
|NA|A grinding, cutting and polishing<br>process with emissions captured<br>by dust collector vented indoors|NA|This process is exempt from<br>permitting requirements per the<br>AB Air Quality Code 17.0102<br>(c)(1)(L)(ix).|
