{0}------------------------------------------------
|NA|A ceramic core removal process|NA|This process is exempt from<br>permitting requirements per the<br>AB Air Quality Code 17.0102<br>(c)(1)(L)(x).|
|---|---|---|---|



## **APPLICATION NOTES** 

The application had an error for the emissions associated with EBPVD1 – EBPVD5. The Agency has calculated their emissions with the correction.
{1}------------------------------------------------
## **SECTION C DETAILS** 

## **REGULATORY INFORMATION** 

**(Identify the AB Air Quality Regulations reviewed because of this application.  At a minimum, the regulations already listed should be reviewed and reason given for applicability or nonapplicability.  If a regulation has a standard, list the standard and indicate how the source is in** 

## **compliance.)** 

|**SECTION C DETAILS**|**SECTION C DETAILS**|**SECTION C DETAILS**|
|---|---|---|
|**REGULATORY INFORMATION**<br>**(Identify the AB Air Quality Regulations reviewed because of this application.  At a minimum, the**<br>**regulations already listed should be reviewed and reason given for applicability or non-**<br>**applicability.  If a regulation has a standard, list the standard and indicate how the source is in**<br>**compliance.)**|||
|**AB Air Quality Regulation Number / Title**|**Emission**<br>**Source ID**<br>**No(s).**<br>**Subject**|**Notes On Regulation**<br>(Compliance demonstration, applicability, etc.)|
|17.0500 – Title V Procedures|NA|The facility does not have potential emissions above<br>the applicability threshold of 100 tons per year for any<br>criteria pollutant, 25 tons per year for any combination<br>of hazardous air pollutants, or 10 tons per year for any<br>individual hazardous airpollutant.|
|17.0700 – Toxic Air Pollutant Procedures<br>and<br>4.1104 – Toxic Air Pollutant Guidelines|Entire Facility|The facility conducted a NC Air Toxics review. TAPs<br>were found to be below the TAP permitting emission<br>rates (TPERs), except for chromium.  An initial<br>dispersion modeling analysis was performed using<br>AERMOD that determined that the facility would be<br>below the acceptable ambient levels (AALs) for<br>chromium. The emergency generators were exempt<br>from toxics modeling, but a toxics analysis was still<br>required to be conducted by the agency, so the facility<br>modeled for acrolein, benzene, and formaldehyde.<br>The resulting air toxics modeling indicated that the<br>facility would be below the AALs for these pollutants.<br>The associated stack parameters will be included in<br>their permit. The exempt sources which are subject to<br>GACT standards were included for informational<br>purposes only.  For further information, please see the<br>modeling memo dated December 23, 2020. In 2025<br>the facility updated a recipe for their ALUM1 process<br>which resulted in the PTE for Hydrogen Fluoride<br>surpassing the TPER limit. The facility conducted a<br>dispersion modeling analysis using AERSCREEN and<br>the results will be reflected in this permit modification.<br>A permit limitation of 15.9 lbs of activator per 24-hour<br>period for the ALUM1 process will be added to the<br>permit.|
|4.0524 – New Source Performance<br>Standards (40 CFR 60, Subpart JJJJ)|EGEN1 –<br>EGEN8|These engines are subject to 40 CFR Part 60,<br>Subpart JJJJ – Standards of Performance for<br>Stationary Spark Ignition Internal Combustion<br>Engines, which requires the manufacturer to certify<br>that the generators meet the emission limits listed in<br>the subpart. The generators must be equipped with<br>non-resettable hour meters, and nonemergency use<br>(e.g., testing)islimited to100hours peryear.|
|4.0530 – Prevention of Significant<br>Deterioration|NA|The facility does not have potential emissions above<br>the threshold of 250 tons/year for any criteria<br>pollutant.|
|4.1111 – MACT (40 CFR 63, Subpart<br>ZZZZ)|EGEN1 –<br>EGEN8|Because these generators commenced construction<br>after June 12, 2006, they are considered new sources<br>(located at an area source of HAP emissions), making<br>them subject to 40 CFR Part 63, Subpart ZZZZ –<br>National Emission Standards for Hazardous Air<br>Pollutants for Reciprocating Internal Combustion<br>Engines.  Compliance with NESHAP Subpart ZZZZ is<br>achieved by compliancewith NSPS Subpart JJJJ.|
|4.1111 – MACT (40 CFR 63, Subpart<br>WWWWWW)|VPS1-VPS6|The process is subject 40 CFR Part 63, Subpart<br>WWWWWW – National Emission Standards for<br>Hazardous Air Pollutants: Area Source Standards for<br>Plating and Polishing Standards.  The applicable part<br>of the rule applies to the thermal spraying operation.<br>The rule requires the facility to operate a capture<br>system that collects PM emissions from the thermal<br>spraying process and transports the emissions to a<br>fabric, cartridge, or HEPA filter . There are also<br>recordkeeping andrecordingrequirements.|
