{0}------------------------------------------------
## **AGREEMENT FOR DESIGN CONSULTANT SERVICES** 

This Agreement for Design Consultant Services is made, and entered into this the   1[st] day of  July    2026, by and between the **COUNTY OF BUNCOMBE** , a political subdivision of the State of North Carolina, (hereinafter “OWNER”), and Method Studio, Inc.  , (hereinafter “DESIGNER” or “DESIGN CONSULTANT”), whose principal place of business is:  5 W. Hargett St., Ste 1000, Raleigh, NC 27601. 

For Professional Services in connection with the Project known as: Buncombe County Government Buncombe County Community Resiliency Center 

The Owner and the Design Consultant hereby agree as set forth below: 

## 1. **ARTICLE 1 DEFINITIONS** 

The following words and phrases where appearing in initial capitalization, shall for the purposes of this Agreement have the following meanings: 

- 1.1. Project. The Project shall be as described above. 

- 1.2. Services. The Services to be performed by the Design Consultant under this Agreement shall consist of the Basic Services described in Article 3 and Article 7 and any other services in the Contractor Documents as part of the Basic Services, and include normal structural, mechanical and electrical architectural design services. 

- 1.3. Construction Contract Documents. The Construction Contract Documents shall consist of the plans and specifications prepared by the Design Consultant, and any addenda and change orders thereto, and the Construction Contract between Owner and Contractor, all of which shall be compatible and consistent with this Agreement. 

- 1.4. Construction Costs. The Construction Costs shall be the total cost or estimated cost to the Owner of all elements of the Project designed or specified by the Design Consultant. The Construction Cost shall include the cost at current market rates of labor and materials furnished by the Owner and equipment designed, specified, selected or specially provided for by the Design Consultant, plus a reasonable allowance for the Contractor’s overhead and profit. In addition, a reasonable allowance for contingencies shall be included for market conditions at the time of bidding and for changes in the Work during construction. Construction Costs do not include the compensation of the Design Consultant and its consultants, the costs of the land, rights-of-way, financing or other costs which are the responsibility of the Owner as provided in Article 6. 

- 1.5. Contractor. The Contractor is the person or entity which enters into an agreement with the Owner to perform the construction of any or all of the Project, including, without limitation, the providing of labor, materials, and equipment incorporated or to be incorporated into the Project. The term “Contractor” means the Contractor or its authorized representative, but excludes the Owner’s Representative and the Design Consultant.
{1}------------------------------------------------
- 1.6. Basic Services Compensation. Basic Services Compensation shall be the lump sum fee designated in Article 4 to be paid by the Owner to the Design Consultant in connection with the performance of the Basic Services by the Design Consultant. 

## 2. **ARTICLE 2 RELATIONSHIP OF THE PARTIES** 

- 2.1. Design Consultant Services. The Design Consultant shall provide professional engineering services for the Project in accordance with the terms and conditions of this Agreement and all applicable codes and laws. The Design Consultant’s performance of services shall be as professional consultant to the Owner to carry out the activities of Project design and construction administration and to provide the technical documents and supervision to achieve the Owner’s Project objectives. 

- 2.2. Owner Representation. The Owner shall designate a Project Manager to serve as the Owner’s Representative. The Owner’s Representative has no design responsibilities of any nature. None of the activities of the Owner’s Representative supplant or conflict with the design, budget or any other services and responsibilities customarily furnished by the Design Consultant or subconsultants in accordance with generally accepted architectural/engineering practices except as otherwise modified by this Agreement. Instructions by the Owner to the Design Consultant relating to services performed by the Design Consultant will be issued or made by or through and in accordance with procedural, organizational, and documentation standards established by the Owner’s Representative. Communications and submittals of the Design Consultant to the Owner and Contractor shall be in writing and issued or made in accord with similar procedural and documentation standards established by the Owner’s Representative. The Owner’s Representative shall have the authority to establish procedures, consistent with this Agreement, to be followed by the Design Consultant and Contractor and to call periodic conferences to be attended by the Design Consultant, and his sub-consultants, throughout the term of this Agreement. 

- 2.3. Other Consultants. The Owner may provide drawings, consultation, recommendations, suggestions, data and/or other information relating to the Project from other Consultants under separate contract with the Owner, including but not limited to: Surveyor, Utility Locating Service, Geo-technical Consultant, CMARs, and/or Materials Testing Consultant. The Design Consultant is responsible for the coordination of survey, existing utility location, geo-technical services, and/or material testing, including all coordination with surveyor, soils engineers, utility locating contractor, City and/or County officials, and CMARs, if any, required for Project. 

- 2.4. Design Consultant Representation. 

   - 2.4.1. The Design Consultant shall provide a list of all consultants (and sub-consultants if applicable) which the Design Consultant intends to utilize on the Project prior to commencing work on the Project. The list shall include such information on the qualifications of the consultants as may be requested by the Owner. The Owner will review the consultants proposed. The Design Consultant shall not retain a consultant to which the Owner has a reasonable objection. The Design Consultant shall use individuals or firms that are licensed and regularly engaged in the fields of expertise required for this Project. 

   - 2.4.2. All agents and workers of the Design Consultant and its sub-consultants shall be prepared to provide identification at all times they are on the Owner’s property including, at a minimum, the company name and telephone number and name.  The County reserves the right to require identification badges that contain the information above. 

   - ’
{2}------------------------------------------------
- 2.4.3. The Design Consultant shall receive, compile and report all M/WBE participation of all of its sub-consultants and vendors of this project in a format acceptable to Owner at the commencement of design, and on a monthly basis, should any change from the preliminary submission occur. 

- 2.5. Division of Responsibilities/Services. The Design Consultant understands and agrees that should the Owner’s Representative or other consultant provide the Design Consultant with any estimating assistance, cost or time control recommendations or other consultation, recommendations or suggestions, any or all such activities on the part of the Owner’s Representative, consultant, or any other representative of the Owner shall in no way relieve the Design Consultant of the responsibility of fulfilling its obligations and responsibilities under this Agreement. 

- 2.6. Compliance with Laws. Design Consultant represents that it is in compliance with all applicable Federal, State, and local laws, regulations or orders, as amended or supplemented, including Chapter 64 Article 2 of the North Carolina General Statutes regarding the verification of work authorization. The implementation of this Contract shall be carried out in strict compliance with applicable Federal, State, or local laws. 

## 3. **ARTICLE 3 BASIC SERVICES** 

## 3.1. **Scope of Services** . 

- 3.1.1. The Basic Services to be provided by the Design Consultant shall be performed in the phases described hereinafter which have as their objective design and construction administration of the Project. The Basic Services shall be performed in accordance with the standard of care set forth in this Agreement. The final product shall be suitable for the Owner’s purposes, satisfy the Owner’s requirements, comply with all applicable codes and laws, and be completed on a timely basis and within the approved budget. 

- 3.1.2. The Design Consultant’s services shall be performed as expeditiously as necessary for the orderly progress of the Work. The Design Consultant shall submit for the Owner’s approval a schedule for the performance of the Design Consultant’s services which may be adjusted as the Project proceeds, and shall include allowances for periods of time required for the Owner’s review and for approval of submissions by authorities having jurisdiction over the Project. Time limits established by this schedule approved by the Owner shall not, except for reasonable cause, be exceeded by the Design Consultant. 

- 3.1.3. Upon authorization from the Owner to proceed, and based on the approved Design Narrative, the Design Fee, and Preliminary Programming, the Design Consultant shall prepare **Schematic Design Documents** consisting of drawings and other documents illustrating the design concept, scale and relationship of the Project components, for approval by the Owner. 

## 3.2. **Design Development Phase** . 

- 3.2.1. Based on the approved Schematic Design Documents and any adjustments authorized by the Owner in the program, schedule or construction budget, the Design Consultant shall prepare, for approval by the Owner, Design Development Documents consisting of drawings and other documents to fix and describe the size and character of the project as to, structural, mechanical and electrical systems, materials and such other elements as may be appropriate.
{3}------------------------------------------------
- 3.2.2. The Design Consultant shall advise the Owner of any adjustments to the preliminary estimate of Construction Costs 

## 3.3. **Construction Document Phase** . 

- 3.3.1. Upon written authorization from the Owner to proceed, the Design Consultant shall prepare from the approved Design Documents, working drawings and Specifications setting forth in detail the requirements for the construction of the entire Project. The Design Consultant shall assist the owner in the preparation of the necessary bidding information, bidding forms, the Conditions of the Contract, and the form of Agreement between the Owner and Contractor. 

- 3.3.2. The Design Consultant shall assist the Owner in connection with the Owner’s responsibility for filing documents required for the approval of governmental authorities having jurisdiction over the Project. 

- 3.3.3. The Design Consultant shall be responsible for, and shall hold the Owner harmless for, any and all claims or damages due to the negligence of the Design Consultant or his employees in the preparation of the Construction Documents. 

## 3.4. **Permitting and Bidding/Negotiation** . 

- 3.4.1. The Design Consultant, following the Owner’s approval of the Construction Documents and of the latest preliminary estimate of Construction Costs, shall assist the Owner in obtaining bids or negotiated proposals and assist in awarding and preparing contracts for construction. 

- 3.4.2. The Design Consultant shall coordinate and document the reproduction, distribution and retrieval of the bidding documents. Further, the Design Consultant shall coordinate and document the collection and return of deposits or payments. In addition to the bidders, documents shall be issued to all required code authorities, contractors, plan room, services, and others, as the Owner designates. 

## 3.4.3. _Intentionally left blank for numbering purposes._ 

- 3.4.4. The Design Consultant shall request, expedite and submit all information necessary to obtain all necessary permits, licenses and approvals, required for the Project. 

- 3.4.5. The Design Consultant shall prepare such clarifications and addenda to the bidding documents as may be required. The Design Consultant will provide these to the Owner for review prior to issuance to all holders of bid documents. 

- 3.4.6. The Design Consultant will schedule and conduct a Pre-Bid Conference with prospective bidders to review the Project. The Design Consultant shall provide knowledgeable representatives, including representatives of its consultants, to participate in these conferences to explain and clarify Bidding Documents. Within two (2) days after the Prebid Conference the Design Consultant shall deliver to the Owner, if needed, a final Addendum.
{4}------------------------------------------------
- 3.4.7. The Design Consultant shall prepare a certified bid tabulation and recommendation to the Owner concerning the Contract Award. 

- 3.4.8. If the estimated Construction Costs are exceeded by the lowest bona fide bid or negotiated proposal, the Owner shall, i) give written approval of an increase in such fixed limit, ii) authorize rebidding or renegotiating of the project within a reasonable time, iii) abandon the Project and terminate in accordance with Article 12, OR iv) participate with the Design Consultant in such re-bidding, re-negotiation, and re-design, at no additional expense to the Owner, as may be necessary to obtain price(s) within the approved budget or price(s) acceptable to the Owner. All re-design must be approved by the Owner. The Design Consultant, without additional charge, shall modify the Contract Documents as necessary to comply with the fixed limit, if established as a condition of this Agreement 

- 3.4.9. Should the Design Consultant re-design or conduct re-bidding under its responsibilities set out in the preceding paragraph, its’ Construction Phase and Post Construction Phase services shall be extended to take re-design/re-bid delays into account at no additional expense to the Owner. 

- 3.4.10. The Design Consultant shall assist the Owner’s Representative in the preparation of the Agreement(s) between Owner and Contractor(s) for the Owner’s execution. The Owner’s Representative will coordinate award(s) and Notice(s) to Proceed for the Owner. 

## 3.5. **Construction Phase** . 

- 3.5.1. The Construction Phase for each portion of the Project will commence with the award of the Construction Contract and will terminate when the Owner makes the Final Completion payment to the Contractor. 

- 3.5.2. The Design Consultant shall consult with the Owner and participate in all decisions as to the acceptability of subcontractors and other persons and organizations proposed by the Contractor for various portions of the work. 

- 3.5.3. The Design Consultant shall receive, compile, track and report all W/MBE participation of all contractors, sub-contractors and vendors of this project in a format acceptable to Owner. Reports will be made to the Owner on a monthly basis, utilizing a pay application cover sheet to be supplied and certified by the contractor (format to be provided by Owner). 

- 3.5.4. The Design Consultant shall review and approve the Work performed by the Contractor(s) for conformance with Contract Documents. 

- 3.5.5. The Design Consultant shall provide necessary Project drawings, in electronic format, to the electrical or data contractor for creation of data “as built” submittal and approval drawings, and to the general contractor for site layout/staking. 

- 3.5.6. The Design Consultant shall conduct Pre-installation meetings to review the installation procedures prior to the placement of the work. 

- 3.5.7. The Design Consultant shall, when requested by the Owner’s Representative, prepare Change Order documentation.
{5}------------------------------------------------
- 3.5.8. The Design Consultant shall render to the Owner’s Representative, within two (2) working days unless otherwise authorized by the Owner’s Representative, interpretations of requirements of the Contract Documents. The Design Consultant shall make all interpretations consistent with the intent of and reasonably inferable from the Contract Documents. 

- 3.5.9. Should errors, omissions or conflicts in the specifications or other Contract Documents by the Design Consultant be discovered, the Design Consultant will prepare and submit to the Owner’s Representative, within two (2) working days unless otherwise authorized by the Owner’s Representative, such amendments or supplementary documents and provide consultation as may be required, for which the Design Consultant shall make no additional charges to the Owner. 

- 3.5.10. The Owner’s Representative shall be the point of contact for the Owner, except when the Owner shall direct otherwise. All instructions to the Contractor(s) shall be issued by the Design Consultant except when is directed otherwise by the Owner’s Representative. 

- 3.5.11. The Design Consultant will have access to the Work at all times. All site visits, observations and other activities by the Design Consultant shall be coordinated with the Owner’s Representative and written report of such visits made promptly to the Owner’s Representative. 

- 3.5.12. The Design Consultant shall make such periodic visits to the Project sites as may be necessary to familiarize themselves generally with the progress and quality of the Work and to determine in general if the Work is proceeding in accordance with the Contract Documents. On the basis of such on-site observations, the Design Consultant and its consultants shall take the appropriate steps to guard the Owner against defects and deficiencies in the Work of the Contractor. If the Design Consultant observes any work that does not conform to the Contract Documents, the Design Consultant shall immediately make an oral and written report of all such observations to the Owner’s Representative. The Design Consultant shall not be required to make exhaustive or full-time on-site observations to check the quality or quantity of the Work, but shall make as many observations as may be reasonably required to fulfil their obligations to the Owner. The Design Consultant shall not be responsible for construction means, methods, techniques, sequences or procedures, or safety precautions and programs in connection with the Work. 

- 3.5.13. The Design Consultant shall immediately notify the contractor and Owner in writing if the Project falls more than fourteen (14) days (or the number of days set by the County in the preconstruction meeting, which number shall be recorded in the minutes of said meeting) behind schedule.  The Design Consultant shall immediately request a recovery plan from the contractor and make appropriate written recommendation to the Owner. 

- 3.5.14. Based upon observations at the site and upon the Contractor’s applications for payment, the Design Consultant shall determine the amount owing to the Contractor(s), pursuant to the terms of the Owner/Contractor Agreement, and shall issue Certificates for Payment to the Owner in such amounts. The Design Consultant’s signing of a Certificate of Payment shall constitute a representation by the Design Consultant to the Owner, based upon the Design Consultant’s observations at the site and the data comprising the Application for Payment, that the Work has progressed to the point indicated, that to the best of the Design Consultant’s knowledge, information and belief, the quality of the Work appears to be in accordance with the Contract Documents (subject to: an evaluation of the Work for
{6}------------------------------------------------
conformance with the Contract Documents upon Substantial Completion; the results of any subsequent tests required by the Contract Documents; minor deviations from the Contract Documents correctable prior to completion; and to any specific qualifications stated in the Certificate for Payment), and that the Contractor is entitled to payment in the amount certified. By signing a Certificate for Payment to the Owner, the Design Consultant shall not be deemed to represent that it has made any examination to ascertain how and for what purpose the Contractor has used the monies paid on account of the Construction Contract Sum. 

- 3.5.15. If, in accordance with its duty, the Design Consultant advises the Owner’s Representative of non-conforming work as stated in subparagraph 3.5.12, the Design Consultant shall confirm the non-conformance in writing to the Owner’s Representative within two (2) days of observation. 

- 3.5.16. The Design Consultant and the Owner’s Representative jointly shall have authority to condemn or reject Work on behalf of the Owner when in the Owner’s Representative’s or the Design Consultant’s opinion the Work does not conform to the Contract Documents. Whenever in the Owner’s Representative’s or the Design Consultant’s reasonable opinion it is considered necessary or advisable to insure the proper implementation of the intent of the Contract Documents, the Owner’s Representative shall have the authority to require special inspection or testing of any Work in accordance with the provisions of the Contract Documents whether or not such Work is fabricated, installed or completed. 

## 3.6. **Final Completion of Design Services** . 

- 3.6.1. When the Contractor notifies the Design Consultant that the Work is substantially complete, the Design Consultant and its consultants shall inspect the Work and prepare and submit to the Owner’s Representative lists of the Work of the Contractor(s) which is not in conformance with the Contract Documents. The Design Consultant shall transmit such lists to the Contractor(s). The Owner may request that the Design Consultant inspect and prepare a list on any portion of the Work. 

- 3.6.2. The Design Consultant shall receive, compile, and report all W/MBE participation of all contractors, sub-contractors and vendors of this project, utilizing a pay application cover sheet to be supplied and certified by the contractor (format to be provided by Owner). 

- 3.6.3. The Design Consultant and its consultants shall conduct up to two (2) comprehensive Final Completion inspections at the request of the Owner. If more than two (2) Final Completion inspections are required, through no fault of the Design Consultant, the additional inspections shall be deemed additional services. 

- 3.6.4. The Design Consultant shall obtain from the Contractor(s) drawings, prints, and other data necessary for the accurate preparation of the record drawings. 

- 3.6.5. The Design Consultant shall make a recommendation in writing to the Owner regarding liquidated damages for each contractor, as may be applicable. 

- 3.6.6. Upon correction of the deficiency reports and acceptance of all other close-out submittals and certificates of the Contractor, the Owner’s Representative and the Design Consultant shall review and approve the Application for Final Payment and forward it to the Owner
{7}------------------------------------------------
for execution. In addition, the Design Consultant shall certify in writing that the work conforms to the Contract Documents. The Design Consultant shall issue AIA Substantial Completion Certificates for each Contractor. 

## 3.7. **Serving as Witness** . 

- 3.7.1. The Design Consultant shall provide testimony in public hearings, arbitration proceedings, and legal proceedings, and such testimony shall be provided without additional fee or charge to the Owner unless said testimony is requested by the Owner and consists of expert testimony not related to this Project or Work. 

## 3.8. **Construction Warranty** . 

- 3.8.1. The Design Consultant and its consultants shall assist the Owner in resolution of warranty issues as may be required to determine responsibility for deficiencies. The Design Consultant and its consultants shall conduct an inspection of the project one (1) month prior to warranty expiration and provide to the Owner a written report specifying any warranty deficiencies which may exist. 

## 4. **ARTICLE 4 COMPENSATION** 

## 4.1. **Basic Services Compensation** . 

The Owner shall compensate the Design Consultant in accordance with the terms and conditions of this Agreement, including the following: 

- 4.1.1. For the Basic Services of the Design Consultant, Basic Services Compensation shall be in the amount of      $1,599,220.00       . 

- 4.1.2. In the event the Owner requests changes to the Project or elects not to complete the work or any portion thereof, which would decrease the most recently approved CCAP, basic compensation due the Design Consultant, as to such deletion or decrease, shall be adjusted downwards for remaining services to be performed but not for services already performed to the date of receipt by the Design Consultant of the written requested change or notice of the intent not to complete part or all of the work, in accordance with the basic payment schedule set forth in Paragraph 4.2 hereof. 

- 4.1.3. The Basic Services Compensation stated in Paragraph 4.1.1 includes all compensation and other payments due the Design Consultant (manpower, overhead, profit, direct costs, travel, copies, postage, telephone and facsimile service, etc.) in the performance of the Basic Services. 

## 4.2. **Payments to the Design Consultant** . 

Payments on account of the Design Consultant shall be made as follows: 

- 4.2.1. Payments for Basic Services, including any design phase change orders, shall be made in proportion to services performed so that the compensation at the completion of each Phase shall equal the following percentages of the Basic Services Compensation.
{8}------------------------------------------------
Payment shall be made upon presentation of the Design Consultant’s statement of services, fully supported by invoices, time cards, and certifications that all subconsultants have been paid, and other documentation as requested by the Owner. 

|Schematic Design Phase|15%|
|---|---|
|Design Development Phase|20%|
|Construction Documents Phase|40%|
|Permitting and Bidding/Negotiation Phase|5%|
|Construction Administration (to include Close Out Documents)|20%|
|Final Completion of Design Services Phase|100%|



   - 4.2.2. No deductions shall be made from the Design Consultant’s Basic Services Compensation on account of penalty, liquidated damages, retainage or other sums withheld from payments to Contractor. 

   - 4.2.3. Deductions may be made from the Design Consultant’s Basic Services Compensation on account of errors and omissions in the drawings, specifications and other documents prepared by the Design Consultant or in the Design Consultant’s performance of its obligations under this Agreement. 

- 4.3. Additional Services Compensation. 

   - 4.3.1. With respect to any Additional Services, as described in Article 7 herein, performed by the Design Consultant hereunder, the Design Consultant and Owner shall negotiate an equitable adjustment to the Basic Services Compensation. However, if negotiations are not successful prior to the time the additional services are needed, the Owner may direct the Design Consultant to proceed with the Additional Services on a time spent basis with Additional Services Compensation to be computed as follows: 

   - 4.3.2. Principals’ time at the fixed rate as stated in the proposal submitted by the designer and attached as Exhibit A. 

   - 4.3.3. Payments for Additional Services of the Design Consultant shall be made upon presentation of the Design Consultant’s statement of services, fully supported by invoices, time cards, and other documentation as requested by the Owner. 

- 4.4. Accounting Records. 

   - 4.4.1. Records of the Design Consultant with respect to Additional Services and payroll, and consultant and other expenses (including Reimbursable Expenses) pertaining to the Project, shall be kept according to generally accepted accounting principles and shall be available to the Owner or its authorized representative for inspection and copying at mutually convenient times. 

## 5. **ARTICLE 5 PERIOD OF SERVICE** 

- 5.1. Unless earlier terminated as provided in Article 12 hereof, this Agreement shall remain in force for a period which may reasonably be required for the Basic Services and Additional Services hereunder. However, the provisions of the Agreement relating to Professional Responsibility
{9}------------------------------------------------
Construction Warranty; Professional Liability coverage; Indemnification; and Ownership of Documents/Confidential Information shall remain in effect after termination of the other provisions of the Agreement. 

- 5.2. Time is of the essence in this Agreement. 

## 6. **ARTICLE 6 OWNER’S RESPONSIBILITIES** 

- 6.1. The Owner shall provide full information regarding the requirements for the Project. 

- 6.2. The Owner shall examine documents submitted by the Design Consultant and shall render decisions pertaining thereto promptly, to avoid unreasonable delay in the progress of the Design Consultant’s Services. 

- 6.3. If required for this Project, the Owner shall furnish a certified land survey of the Project sites, giving as applicable, grades and lines of streets, alleys, pavements and adjoining property; rights-of-way, restrictions, easements, encroachments, zoning, deed restrictions, boundaries and contours of the site; locations, dimensions and data pertaining to existing buildings, other improvements and trees; and full information concerning available service and utility lines, both public and private, above and below grade, including inverts and depths. All associated work will be coordinated by Design Consultant as part of the Basic Services. 

- 6.4. The Owner shall pay for the services of a soils engineer or other consultant, when such services are deemed necessary by the Design Consultant or Owner’s Representative, to provide reports, test borings, test pits, soil bearing values, percolation tests, air and water pollution tests, ground corrosion and resistively tests and other necessary operations for determining subsoil, air and water conditions, with appropriate professional interpretations thereof. All associated work will be coordinated by Design Consultant as part of the Basic Services. 

- 6.5. All services, information, surveys and reports required of the Owner shall be furnished at the Owner’s expense. 

- 6.6. If the Owner so directs, the Owner shall pay for and the Design Consultant shall request, expedite, and obtain all necessary permits, licenses, approvals, easements, assessments, and charges required for the construction, use or occupancy of permanent structures or for permanent changes in existing facilities. 

## 7. **ARTICLE 7 ADDITIONAL SERVICES** 

- 7.1. If any of the following Additional Services are authorized in advance by the Owner in writing, the Design Consultant shall furnish or obtain from others the authorized Additional Services. If authorized in advance, in writing by the Owner, the Design Consultant shall be paid for these Additional Services by the Owner pursuant to Article 4.3, to the extent they exceed the Basic Services under this Agreement. Additional Services may include: 

   - 7.1.1. Providing fully detailed presentation models or presentation renderings, not included in Basic Services. 

   - 7.1.2. Providing financial feasibility or other special studies, not included in Basic Services.
{10}------------------------------------------------
- 7.1.3. Providing planning surveys or alternative site evaluations. 

- 7.1.4. Providing services after payment by the Owner of the Final Payment to the Design Consultant other than services called for in the Basic Services. 

- 7.1.5. Providing any other services not otherwise included in this Agreement or not customarily furnished in accordance with generally accepted architectural practices consistent with the terms of this Agreement. 

## 8. **ARTICLE 8 NOTICES** 

- 8.1. Any notice required by this Agreement or other communications to either party by the other shall be in writing and deemed given when delivered personally or when deposited in the United States Post Office, first class, postage prepaid, addressed as follows, or to such other address as shall be duly given by notice meeting the requirement of this Article. 

To Owner: 

Buncombe County Attn: General Services Department 2945 Riverside Drive Buncombe, NC 28804 

To Design Consultant: Method Studio, Inc. 5 W. Hargett St., Ste 1000 Raleigh, NC 27601 

## 9. **ARTICLE 9 INSURANCE** 

- 9.1. Insurance 

   - 9.1.1.Design Consultant agrees their insurance policies shall be endorsed evidencing the minimum insurance coverage and limits set forth below prior to the Owner’s signing of this Agreement. The insurance coverage and limits set forth below shall be deemed minimum coverage limits and shall not be construed in any way as a limitation on Design Consultant’s duty to carry adequate insurance. The insurance coverage and limits set forth below shall not act as, be construed, or deemed to be a limitation on the liability of Design Consultant, for losses or damages under this Agreement.  The minimum insurance coverage which the Design Consultant shall procure and maintain at its sole cost and expense during the term of the Agreement is as follows: 

**Worker’s Compensation** . Coverage at the statutory limits in compliance with applicable State and Federal laws. Design Consultant shall ensure that any subcontractors also have workers compensation coverage at the statutory limits. 

**Employer’s Liability.** Coverage with minimum limits of $1,000,000 each employee accident and $1,000,000 each employee disease.
{11}------------------------------------------------
**Commercial General Liability.** Insurance covering all operations performed by the Design Consultant with a minimum limit of $1,000,000 per occurrence with a $2,000,000 aggregate. 

**Professional Liability.** Insurance covering the Design Consultant for acts, errors, or omissions in performance of the Agreement with a minimum limit of $1,000,000 per claim for projects under $15,000,000 and a minimum limit of $2,000,000 per claim for projects over $15,000,000. 

**Business Automobile Liability.** Insurance covering all owned, non-owned, and hired vehicles used in performance of this Agreement.  The minimum combined single limit per occurrence shall be $1,000,000 and shall include uninsured/underinsured motorist coverage per N.C. Gen. Stat. § 20-279.21. 

**Umbrella/Excess Liability.** If the underlying liability policy limits are less than those required, Design Consultant may provide an excess or umbrella policy to meet the required limits of insurance.  The excess or umbrella policy shall extend coverage over the underlying professional liability policy.  Any additional insured under any policy of the underlying insurance will automatically be an additional insured under this insurance. 

## **Additional Insurance Provisions.** 

If the Design Consultant maintains higher limits than the minimums shown above, the County requires and shall be entitled to coverage for the higher limits maintained by the Design Consultant.  Any available insurance proceeds in excess of the specified minimum limits of insurance and coverage shall be available to the County. 

The Design Consultant shall provide the County with certificates of insurance evidencing the above amounts.  Buncombe County and    General Services Department      shall be named as additional insureds under the commercial general liability and business automobile liability policy(s). Before commencing work and for any subsequent renewals, the Design Consultant shall furnish the County with certificates of insurance on an approved form. 

Each insurance policy required above shall state that coverage shall not be canceled, except with written notice to the County, delivered in accordance with the policy provisions.  All insurance shall be procured from reputable insurers authorized and qualified to do business in North Carolina and in a form acceptable to the County. 

Design Consultant shall require and verify that all subcontractors maintain insurance meeting all the requirements stated herein, and Design Consultant shall ensure that Buncombe County and General Services Department      are additional insureds on insurance required from subcontractors. 

The Design Consultant shall maintain in force during the performance of this contract and for six (6) years after final completion of the Project, the Professional Liability insurance coverage referenced above. 

Waiver of Subrogation:  Design Consultant hereby grants to County a waiver of any right to subrogation which any insurer of said Design Consultant may acquire against the County by virtue of payment of any loss under such insurance.  Design Consultant agrees to obtain any endorsement that may be necessary to affect this waiver of subrogation. 

The limits of coverage under each insurance policy maintained by the Design Consultant shall not be interpreted as limiting the Design Consultant’s liability and obligations under this Agreement.
{12}------------------------------------------------
- 9.2. Notwithstanding the foregoing, nothing contained in this Article 9, nor this Contract, shall be deemed to constitute a waiver of the sovereign immunity of the Owner, which immunity is hereby reserved by the Owner. 

## 10. **ARTICLE 10 INDEMNIFICATION** 

- 10.1. Notwithstanding anything to the contrary contained herein, the Design Consultant shall indemnify and hold harmless the Owner and their agents and employees from and against all claims, damages, losses and expenses, including but not limited to attorney’s fees, arising out of or resulting from (1) the Design Consultant’s negligent performance or failure to perform its obligations under this Agreement and (2) any claim, damage, loss or expense attributable to bodily injury, sickness, disease or death, or to injury to or destruction of personal and/or real property including the loss of use resulting wherefrom and caused by any negligent act or omission of the Design Consultant, anyone directly or indirectly employed by the Design Consultant or anyone for whose acts the Design Consultant may be liable. Such obligation shall not be construed to negate, abridge or otherwise reduce any other right or obligation of indemnity which would otherwise exist as to any party or person described in this Article. 

- 10.2. Except as otherwise set forth in this Agreement, the Design Consultant and the Owner shall not be liable to each other for any delays in the performance of their respective obligations and responsibilities under this Agreement which arise from causes beyond their control and without their fault or negligence, including but not limited to, any of the following events or occurrences: fire, flood, earthquake, epidemic, atmospheric condition of unusual severity, war, and strikes. Owner shall not be liable to the Design Consultant for acts or failures to act by the Contractor. 

## 11. **ARTICLE 11 DISPUTE RESOLUTION PROCEDURE** 

- 11.1. To prevent disputes and litigation, it is agreed by the parties that any claim or dispute between the Owner and the Design Consultant, that any claim, dispute, or other matter in question arising out of or related to this Agreement shall be subject to voluntary non-binding mediation as a condition precedent to the institution of legal or equitable proceedings by either party.  If the parties are unable to agree upon a certified mediator to hear their dispute, the President of the Buncombe County Bar Association shall name a mediator to hear the matter. During the pendency of any dispute and after a determination thereof, the parties to the dispute shall act in good faith to mitigate any potential damages including utilization of construction schedule changes and alternate means of construction. The costs of the process shall be divided equally between the parties to the dispute. 

   - 11.1.1. The mediation session shall be private and shall be held in Buncombe County, North Carolina or in another North Carolina County agreed upon by both parties. Mediation under this Article 11 shall not be the cause for a delay of the Project which is the focus of the dispute. 

- 11.2. If, as a result of mediation, a voluntary settlement is reached and the parties to the dispute agree that such settlement shall be reduced to writing, the Mediator shall be deemed appointed and constituted an arbitrator for the sole purpose of signing the mediated settlement agreement. Such agreement shall be, and shall have the same force and effect as an arbitration award, and judgment may be entered upon it in accordance with applicable law in any court of competent jurisdiction.
{13}------------------------------------------------
- 11.3. If the disputed issue cannot be resolved in mediation or either party disagrees with the results of the mediation, the parties may seek resolution in the General Court of Justice in the County of Buncombe and the State of North Carolina. If a party fails to comply in strict accordance with the requirements of this Article, the non-complying party specifically waives all of its rights provided hereunder, including its rights and remedies under State law. 

## 12. **ARTICLE 12** 

## **TERMINATION, SUSPENSION OR ABANDONMENT** 

- 12.1. If either party shall substantially fail to perform in accordance with the terms of this Agreement through no fault of the other party, the non-breaching party may terminate this Agreement by delivering seven (7) days’ written notice of termination. 

- 12.2. If the project is suspended by the Owner for more than thirty (30) consecutive days, the Design Consultant shall be compensated for services performed prior to notice of such suspension. 

- 12.3. This Agreement may be terminated by the Owner upon not less than seven (7) days’ written notice to the Design Consultant in the event that the project is permanently abandoned. If the Project is abandoned by the Owner for more than ninety (90) consecutive days, the Design Consultant may terminate this Agreement by giving written notice. 

- 12.4. If the Owner fails to make payment when due the Design Consultant for services and expenses, the Design Consultant may, upon seven (7) days’ written notice to the Owner, suspend performance of services under this Agreement. Unless payment in full is received by the Design Consultant within seven days of the date of the notice, the suspension shall take effect without further notice. In the event of a suspension of services, the Design Consultant shall have no liability to the Owner for delay or damage caused the Owner because of such suspension of services. 

- 12.5. In the event of termination not the fault of the Design Consultant, the Design Consultant shall be compensated for services performed prior to termination, together with Reimbursable Expenses then due. This shall be the exclusive remedy for termination. 

- 12.6. Owner shall have no liability to the Design Consultant for any delay or damage caused the Design Consultant due to suspension of the work, or due to any other delay, interruption, hindrance, or interference. 

- 12.7. Should the Owner terminate this agreement for any reason under this Article, the Owner will acquire such drawings, including the ownership and use of all drawings, specifications, documents and materials relating to the Project prepared by or in the possession of the Design Consultant. The Design Consultant will turn over to the Owner in a timely manner and in good unaltered condition all original drawings, specifications, documents, materials, and computer files related to the project. 

## 13. **ARTICLE 13 SUCCESSORS/ASSIGNMENT** 

- 13.1. This Agreement shall inure to the benefit of and be binding on the heirs, successors, assigns, trustees and personal representatives of the Owner, as well as the permitted assigns and trustees of the Design Consultant.
{14}------------------------------------------------
- 13.2. The Design Consultant shall not assign, sublet or transfer its interest in this Agreement without the written consent of the Owner, except that the Design Consultant may assign accounts receivable to a commercial bank or financial institution for securing loans, without prior approval of the Owner. 

## 14. **ARTICLE 14 OWNERSHIP OF DOCUMENTS/CONFIDENTIAL INFORMATION** 

- 14.1. The Drawings, Specifications and other documents prepared by the Design Consultant for this Project are for use solely with respect to this Project, the Owner shall be the owner of these documents and shall have all common law, statutory and other reserved rights, including the copyright. The Design Consultant’s Drawings, Specifications or other documents shall not be used by the Owner or others on other projects, except by agreement in writing by the Design Consultant. 

- 14.2. Submission or distribution of documents to meet official regulatory requirements or for similar purposes in connection with the project is not to be construed as publication in derogation of the Owner’s reserved rights. 

## 15. **ARTICLE 15 ADDITIONAL PROVISIONS** 

- 15.1. Unless otherwise provided in this Agreement, the Design Consultant shall have no responsibility for the discovery, presence, handling, removal or disposal of or exposure of persons to hazardous materials in any form at the Project site, including but not limited to asbestos, asbestos products, polychlorinated biphenyl (PCB) or other toxic substances. 

- 15.2. The Design Consultant shall not discriminate against any employee or applicant for employment because of age, gender, race, creed, national origin, or disability. The Design Consultant shall take affirmative action to ensure that applicants are employed and that employees are treated fairly and legally during employment with regard to their age, sex, race, creed, national origin, or disability. In the event the Design Consultant is determined by the final order of an appropriate agency or court to be in violation of any non-discrimination provision of federal, state or local law or this provision, this Agreement may be canceled, terminated or suspended in whole or in part by Owner, and the Design Consultant may be declared ineligible for further Owner contracts. 

- 15.3. The Design Consultant shall follow all applicable federal, state, and local laws. 

- 15.4. The Owner and Design Consultant agree to endeavor to provide written notification and to negotiate in good faith prior to litigation concerning claims, disputes, and other matters in question arising out of or relating to this Agreement or the breach thereof. 

- 15.5. The payment of any sums by the Owner shall not constitute a waiver of any claims for damages by the Owner for any breach of the Agreement by the Design Consultant. 

- 15.6. This Agreement and its Exhibits and Attachments represent the entire and integrated agreement between the Owner and the Design Consultant and supersede all prior negotiations, representations or agreements, either written or oral. This Agreement may be amended only by written instrument signed by both Owner and Design Consultant. 

- 15.7. This Agreement shall be governed by the laws of the State of North Carolina. All actions relating in any way to this Contract shall be brought in the General Court of Justice in the County of Buncombe and the State of North Carolina.
{15}------------------------------------------------
- 15.8. If any one or more of the provisions contained in this Agreement, for any reason, are held to be invalid, illegal, or unenforceable in any respect, such invalidity, illegality or unenforceability shall not affect any other provisions thereof and this Agreement shall be construed as if such invalid, illegal or unenforceable provision had never been contained herein. 

- 15.9. Except where specifically stated otherwise, all periods of time stated in terms of days shall be considered periods calculated in calendar days. 

- 15.10. The headings or captions within this Agreement shall be deemed set forth in the manner presented for the purposes of reference only and shall not control or otherwise affect the information set forth therein or interpretation thereof. 

- 15.11. For the purpose of this Agreement unless the context clearly indicates otherwise, the singular includes the plural, and the plural includes the singular. 

- 15.12. This Agreement may be executed in any number of counterparts, each of which shall be deemed an original, and the counterparts shall constitute one and the same instrument, which shall be sufficient evidence by any one thereof. 

- 15.13. **E-VERIFY** . As a condition of payment for services rendered under this agreement, CONTRACTOR shall comply with the requirements of Article 2 of Chapter 64 of the General Statutes. Further, if CONTRACTOR provides the services to the County utilizing a subcontractor, CONTRACTOR shall require the subcontractor to comply with the requirements of Article 2 of Chapter 64 of the General Statutes as well. CONTRACTOR shall verify, by affidavit, compliance of the terms of this section upon request by the COUNTY. 

In witness whereof, each individual executing this agreement acknowledges that he/she/it is authorized to execute this agreement and further acknowledges the execution of this agreement the day and year first written above. 

This instrument has been preaudited in the manner required by the Local Government Budget and Fiscal Control Act. 

See contract cover form for preaudit signature. 

## **DESIGN CONSULTANT: METHOD STUDIO, INC.** 

By:__________________________________ 

Title:_________________________________ Date:_________________________________ 

**OWNER: COUNTY OF BUNCOMBE** 

By:__________________________________ Title:_________________________________ Date:_________________________________
{16}------------------------------------------------
```
ATTACHMENT A
```

**==> picture [152 x 72] intentionally omitted <==**

November 19, 2025 

Ronnie Lunsford, PEM Facilities Project Manager | General Services Department Buncombe County 40 McCormick Pl. | Asheville, NC 28801 828.775.0853 

## **RE: Architectural Services for Buncombe Co. Community Resiliency Center** 

Thank you for allowing Method Studio the opportunity to provide this fee proposal for architectural design services for Buncombe Co.’s new Community Resiliency Center which will also house the Recreational Services Department in Asheville, North Carolina. This letter will outline services to be rendered by Method Studio in order to provide normal design services to program, design, document, obtain a permit, and provide construction administration services for the new building and will serve as our Letter of Agreement for the project. The list of services to be provided and associated fees have been generated based on experience with similar projects where Method Studio has performed in a similar capacity. 

## **Project Description + Scope** 

## **Base Architectural Design:** 

It is our understanding that the scope of work will encompass approximately 28,000sf that will serve as a vital emergency hub during natural disasters and will also house the Recreational Services Department staff as well as community space. Construction costs are estimated at approximately $535/sf, or $15 million, plus an additional $1.75-$2 million in rooftop photovoltaic solar panels and a Battery Energy Storage System (BESS) to account for one day of resiliency before kicking in generator power (fuel source TBD) during natural disasters. 

The anticipated size of the facility will be validated during programming + concept design.  We will take a master plan approach to capture potential future phases of development / expansion on the site, while taking care to minimize impact to the existing dog park and community garden. Method Studio will thoughtfully prioritize robust upgrades to life safety systems, fire protection, water quality, mold resistance, stormwater drainage, and structural integrity. Special attention will be given to addressing community needs, particularly for young children, adolescents, the elderly, individuals with special needs, and other underserved populations. The design will emphasize clear circulation, safe sightlines, and accessibility to ensure a functional and inclusive environment. Infrastructure enhancements, including street access, telecommunications, off-grid emergency power systems, and emergency water systems will be incorporated. A high-level study of site hazards, community vulnerabilities, and an emergency event overlay plan will be included as part of the study. Emergency preparedness planning, risk mapping, evacuation planning, and other disaster-related services are excluded from this scope and will be provided by others. 

Amenity spaces will include a highly flexible, multi-purpose gymnasium with seating sized for two high school basketball courts, showers/locker rooms and laundry facilities, a commercial kitchen, multi-purpose space and medical supply storage. Exterior programming will feature an enclosed rainwater capture cistern, emergency power generator and storage yard, trash enclosure, reserved parking (100 spaces min), delivery and drop-off zones, and playground areas. 

For the purposes of this proposal, the following assumptions and understandings have been made: 

- The disciplines of Civil, Structural, Mechanical, Electrical, Plumbing and Landscape Architecture will fall under Method Studio’s umbrella, and their associated fees have been included as part of this fee proposal 

- Topography, Boundary and Utility Surveys are required for site design and permitting and have been included in the overall fee. 

- Site is limited to approximately 7 acres – site programming or design beyond the boundary identified may result in added fees 

- Method Studio will assist the owner in determining the construction type 

- Method Studio will attend in-person meetings in Buncombe County every other month for workshops/focus groups, up to 6 total. 

- Method Studio will hold a virtual meeting via Teams once per month for progress updates between workshops/focus groups 

- Cost estimating exercises to be performed during each phase outlined below 

5 W.  Hargett St., Ste.1000 Raleigh, NC  27601 

method-studio.com         919.521.4801 

1
{17}------------------------------------------------
**==> picture [152 x 72] intentionally omitted <==**

Fee is based on an anticipated timeline and phases as outlined below, including review and approval time by Buncombe Co. staff. Defined start and completion dates to be provided upon fee approval. An extension in the schedule may result in added fees: 

- Programming + Concept Design + Cost Model: 8 weeks 

- Schematic Design + Cost Model Update: 8 weeks 

- Design Development + Cost Estimate: 12 weeks 

- Cost & Budget Alignment: 4 weeks 

- Construction Documents: 12-16 weeks 

- Permitting: 8 weeks (to be confirmed with municipality) 

- Bidding & Negotiation: 6-8 weeks 

- Construction Administration: 16-18 months (to be confirmed with contractor) 

Method Studio proposes the following design fees to provide the services outlined above: 

**Table I: Base Architectural Design** 

||**Project Phase / Service:**|**% of**<br>**Fee**|**Fixed Fee:**|**Remarks / Additional Comments:**|
|---|---|---|---|---|
|Phase I:|Programming & Concept Design|5%|$       49,500.00||
|Phase II:|Schematic Design|15%|$     148,500.00||
|Phase III:|Design Development|20%|$      198,000.00||
|Phase IV:|Construction Documents,<br>Permitting,Bidding& Negotiations|35%|$      346,500.00||
|Phase VI:|Construction Administration|25%|$      247,500.00||
||**Subtotal Architectural Fees:**||**$ 990,000.00**|**Base architectural fee is based on an**<br>**estimated construction budget of $16.5**<br>**million. Fee to be adjusted if construction**<br>**costs increase more than 20%**|
||Cost Estimating||$        31,910.00|Cost Estimating fees provided by 35North. See<br>consultants’ proposal for more details.|
||Mechanical, Electrical and<br>Plumbing Engineering Design<br>Fees,includingFire Protection||$      243,000.00|Mechanical, Electrical, Plumbing and Fire Protection<br>fees provided by Optima Engineering. See Engineer’s<br>proposal for more detail.|
||Structural Engineering Design<br>Fees||$      136,000.00|Structural, Civil and Landscape Architecture Design<br>fees provided by Stewart Engineering. See Engineer’s<br>proposals for more detail.|
||Civil Engineering Design Fees||$        70,500.00||
||Landscape Architect Design Fees||$        98,500.00||
||**Subtotal Engineering Fees:**||**$   579,910.00**||
||Civil Surveying including<br>Topographical, Boundary and<br>Utility||$        29,310.00|Surveying fees provided by Stewart Engineering|
||**Subtotal Additional Consulting**<br>**Fees:**||**$      29,310.00**||
||MS Consultant Administration Fee||$        60,922.00|Based on 10% of actual consultant fee.|
||**_Professional Discount_**||**_($  60,922.00)_**||
||**Total Design Fees**||**$1,599,220.00**|**Billing occurs monthly as a percentage of work**<br>**completed, or at the end of each phase, whichever**<br>**comes first.**|



**Table III: Anticipated Reimbursables:** These are estimates, will be billed as actual. See additional information under general understandings & assumptions, page 4 

|Item I:|Printing:|$1,235.00|See break out detailpage 4|
|---|---|---|---|
|Item 2:|Travel: Mileage (per round<br>trip)|Per trip Estimated at          $   352.80|Approx. 504 miles round trip from Raleigh office to Site.<br>Additional Miles to be billed per occurrence at $0.70<br>centsper mile|
|Item 3|Travel: Hotel|Per staff memberper trip$   200.00|Anticipate 2-3 staff membersper trip, per night|
|Item 4|Travel: Meal Per diem|Per staff memberper day$     59.00|Anticipate 2-3 staff membersper day,per trip|



5 W.  Hargett St., Ste.1000 Raleigh, NC  27601 

method-studio.com         919.521.4801 

2
{18}------------------------------------------------
**==> picture [152 x 72] intentionally omitted <==**

|**Table IV: Additional Services if desired**|**Table IV: Additional Services if desired**|||
|---|---|---|---|
|ADD-01|FF&E Design Consultation for site, common<br>public spaces, amenity space, offices and<br>meetingspaces|$  28,000.00|Based on 200 staff hours at $140/hr, to be confirmed<br>once scope is clearly defined.|
|ADD-02|Integrated Environmental Graphics:<br>Branding,Signage & Wayfinding|$  35,000.00|Based on 250 staff hours at $140/hr, to be confirmed<br>once scope is clearlydefined.|
||LEED Design & Documentation|Excluded||
||Well buildingDesign & Documentation|Excluded||
|ADD-03|Audio Visual EngineeringDesign Fees|$  11,000.00||
|ADD-04|Voice & Data CablingDesign Fees|$  11,000.00||
|ADD-05|SecurityDesign (Access control & CCTV)|$  11,000.00||
||Comprehensive Community Resiliency<br>Planningand Public Outreach Survey|Excluded|Provided by owner, specialty consultant and additional<br>fee can be added upon request|
|ADD-06|Interior Photo Real Renderings: 4 images, 2<br>exterior,2 interior|$10,800.00|3D sketch renderings in Enscape included in basic services|
|ADD-07|Aerial video / 3D animation overlay on drone<br>photography,1-2 minutes|$10,000.00||



## **Method Studio’s scope of work includes the following services:** 

## **Programming & Concept Design:** 

Method Studio will work collaboratively with leadership to develop an overall vision for the project which includes specific project goals. We will simultaneously work to outline program data and space requirements. Method Studio will meet with leadership to establish team responsibilities, methods of approval, project procedures and schedule requirements. Once program verification is complete, Method Studio will develop a graphic representation of the site plan, building massing and interior spaces. Two (2) minor revisions will be provided, if necessary, as part of this phase. Additional revisions are billed hourly per fee structure below. A preliminary cost estimate is included as part of this phase. 

## **Schematic Design / Design Development Material Selection Phase (SD & DD):** 

Preliminary concepts and finish materials will be presented & coordinated during this phase. Upon approval of the massing and space plan, Method Studio will coordinate aspects of the buildout process with consultants, i.e., mechanical, electrical, and plumbing, as necessary to finalize the schematic design. Method Studio will conduct a review of governing codes & local requirements. Method Studio will provide drawings & documents to establish the final relationships, sizes, scope, and appearance of the project, including major dimensions, materials, and finishes. Coordination with the cost estimating consultant is included at the conclusion of each of these phases. Owner requested revisions made after the space plan and conceptual designs have been approved are billed hourly per fee structure below. 

## **Construction Document Phase (CD):** 

Upon the approval of the schematic & design development documents, Method Studio will develop the necessary plans, elevations, sections, details, schedules, and specifications of the project. This phase involves the documentation of the project to prepare for bidding and permitting. Method Studio will coordinate with consultants, including a final cost estimate. 

## **Permitting Phase:** 

Method Studio will collaborate with the client to submit plans to the local municipality for Permitting. We will work with the local governing agencies and the designated consultants to resolve any deficiencies or discrepancies in the permit set to address their comments. 

## **Bidding & Negotiation Phase (B&N):** 

Method Studio will coordinate and administer the process of bidding to multiple General Contractors and will work with the owner to select. 

## **Construction Administration Phase (CA):** 

Method Studio will assist the client in administering and coordinating the build-out during construction by providing basic services to be billed hourly during the construction phase. Method Studio will review related submittals, attend construction meetings, make periodic site visits, conduct a final walk, and create a project punch list outlining known deficiencies of the final space as related to the contract documents. Our consultant team will also perform periodic site visits throughout construction and provide observation reports for distribution to the team. At the conclusion of the project, Method Studio will work with the general contractor to compile all required close out documentation. 

5 W.  Hargett St., Ste.1000 Raleigh, NC  27601 

method-studio.com         919.521.4801 

3
{19}------------------------------------------------
**==> picture [152 x 72] intentionally omitted <==**

## **Materials, Furnishings, & Equipment (optional additional service):** 

Method Studio is not affiliated, owned, or associated with any particular product line, furniture provider, or manufacturer. Method Studio accepts no specification fees or incentives from vendors, furniture dealerships, or manufacturers. Should any cost savings or incentives be offered, they will be disclosed and passed directly on to the client. 

FF&E Design option assumes a direct award to vendors & subconsultants without an established design & specification criterion included. Method Studio’s scope of work includes coordinating with vendors for furniture and equipment to provide recommendations on specifications that coordinate with the interior build out and infrastructure. Method Studio to coordinate power & data placement for FF&E, coordinate the locations of core drills and outlets, coordinate backing required in walls, coordinate delivery and installation of the FF&E package, and conduct a final walk and punch list of the FF&E package. 

## **General Understandings & Assumptions:** 

- The creation of As-Built documents for use in the creation of the necessary project electronic files is not included for the defined scope of work. 

- While Method Studio shall work toward completing a thorough analysis of architectural issues for the selected site as related to the project, it is clearly understood that hidden or unknown conditions, issues, requirements, and/or regulations unknown to Method Studio may exist. Although Method Studio shall exercise due diligence in responding to such issues, it is understood that Method Studio cannot be held responsible for unknown conditions and issues related to the project that are unforeseen. 

- Complexity of design and accelerated schedule parameters could require a modification in fees. 

- Services by Engineering Consultants (mechanical/electrical/plumbing/fire protection/civil/landscape) are necessary to complete the work and their fees have been included in this agreement. If desired, Method Studio can assist the owner in the hiring of consultants whose work would be performed under our contract and for additional fees. All professional fees for consultants hired by Method Studio for the project will include a 10% consultant administration fee. 

- Services by additional consultants outside of MEP may be necessary to complete the work and their fees are not included in this agreement. Method Studio will coordinate with the owner’s consultants or can assist the owner in obtaining competitive bids and the hiring of consultants whose work would be performed under Method Studio’s contract. The following consulting services are excluded, such as (but not limited to):  Geotechnical Soils Investigation (including Site-Specific Seismic Study, Observed Site Class Determination, and Infiltration Tests) , Aerial Imaging, Off-site Utilities Design, Land Title Report, Subdivisions and Plats, Legal Descriptions, Zoning Change Application, Planned Development Application, Slope-Stability Analysis, Transportation Study, Traffic Impact Analysis, D.O.T. Permits, Soil Thermal Conductivity Analysis, Hydrological Study, Voluntary Clean-Up Plan, Methane / Radon Gas Mitigation, U.S. A.C.E. Wetland Delineation / Wetland Mitigation Plan, FEMA Flood Plan Mapping, Stream Alternation Plan, Storm Water Discharge Pumping Stations,  Wells / Canals / and Water Rights Services, Septic Systems Design, SWPPP Design/Engineering, Environmental Impact Study, Archeological Report, Existing Building Assessment Services, Hazardous Materials Survey, Structural Assessment of Existing Facilities (Tier 2 / Tier 3), Deep Foundation Systems Design, Building Systems Commissioning, Building Envelope Commissioning, Owner’s Project Requirements (OPR), 3D animations, etc. 

- Specification of Furnishings, Fixtures & Equipment (FF&E) is not included in basic architectural services. The fee does cover the graphic layout of conceptual furnishings necessary to enhance the space plan. 

- Reimbursable expenses are to be compensated at one and one tenth (1.1) times actual expense. Reimbursable expenses include, but are not limited to, mileage for distances greater than 20 miles, travel expenses (airfare, hotel, transportation, meals), reproductions, plotting, mileage, etc. Method Studio anticipates the following reimbursable expenses: 

   1. Mileage from Raleigh, NC to Asheville, NC project site 

   2. Hotel & Meals 

   3. Printing: (For each package) 24” x 36” @ $3 per sheet, 3 sets total at 50 sheets per set:  $450.00, 12”x 18” @ $1.50 per sheet, 9 sets total at 50 sheets per set: $675.00, 8” x 11” @ 10 cents per sheet 500 sheets at $50.00, 11” x 17” @ 12 cents per sheet 500 sheets at $60.00. 

   4. Permits & plan check fees are excluded. 

- Services requested by more than thirty (30) days after Substantial Completion shall constitute an Additional Service. 

- Fee is based on the schedule outlined in the project description on page 1, with an estimated project completion date of Summer of 2029. 

Any additional services requested beyond the scope listed above will be charged at the following hourly rates: 

|Sr. Principal<br>$260<br>Principal<br>$185<br>Sr. Project Manager<br>$180<br>Project Manager<br>$160<br>Sr. Architectural Designer<br>$180<br>Architectural Designer<br>$140<br>Project Architect<br>$150|Sr. Interior Designer<br>$150<br>Interior Designer<br>$125<br>Interior Design Associate<br>$115<br>3D Artist<br>$150<br>Sr. Job Captain<br>$125<br>Job Captain<br>$120<br>Sr. Graphic Designer<br>$150|Graphic Designer<br>$125<br>Architectural Associate<br>$130<br>BIM Specialist<br>$120<br>BIM Technician<br>$115<br>Technical Support<br>$100<br>Administrative<br>$120<br>Clerical<br>$80|
|---|---|---|



5 W.  Hargett St., Ste.1000 Raleigh, NC  27601 

method-studio.com         919.521.4801 

4
{20}------------------------------------------------
**==> picture [152 x 72] intentionally omitted <==**

We are incredibly excited about this important project and thank you for the opportunity to work with Buncombe Co. to help you achieve your goals. Please don’t hesitate to call with any questions. 

Sincerely, 

**==> picture [131 x 39] intentionally omitted <==**

Jenn Celestino, IIDA, LEED AP®, NCIDQ Associate Principal 

**Approved by:** By:     _________________________________________________ Title:  _____________________      Date: ____________________ 

**==> picture [69 x 35] intentionally omitted <==**

Joshua Greene, AIA, NCARB Principal 

5 W.  Hargett St., Ste.1000 Raleigh, NC  27601 

method-studio.com         919.521.4801 

5
